Date   

Re: Android for ExploreStars and Windows for ASCOM?

Wes Mcdonald
 

Ron:

Glad to have you aboard!

The apps and the firmware are not coupled so as to mess one up if you previously used the other.  The only caveat is you have to get the mount into certain communication method modes depending on what you are using.  But go ahead and load the Tab A and use it by all means.  Then load Explorestars on the PC and use it  (one at a time only).  No worries.

But to your other question.  Explorestars will work or wired ASCOM will work, or WiFi ASCOM will work but only one at a time.  You cannot share the PMC-8 controller.  Only one can run the mount.  There are creative ways to mix and match stuff, but in the end, if you are sending mount commands, only one mode or control is supported at any one time.

Lots of this is all over theplace in the forum, and some probably in the FAQs, and some in the Knowledge Base.  Also some in the Programmers Reference MAnual, which is a collection of facts covering many things, not really software and some of it helpful to you.

And of course the Forum members usually get back to you with answers to your questions in fine shape.  Lots of help out here.

You are going to find out that the PMC-8 is quite the value given its performance for the cost.  It does however put in the driver's seat -- meaning you don't just turn it on.  There will be some learning of its ways, which in the process you will learn a lot about telescope mounts, astronomy, and related topics that will serve you well as you progress through the hobby.  But expect to put in some work.

Once again welcome to the hobby and the forum.  Be sure to fill out your signature in the groups.io area, and I believe you need to do so in each subgroup (sorry, I didn't write the code).  

Wes.


--
Wes, Southport NC
EXos2-GT PMC-8, iExos 100
ES ED 127, 10" LX200GPS+wedge, Astro-Tech 8" Newt, ETX-90, 60mm no-name guide scope ~ 260mm FL
Polemaster, Orion ST-80 and SAG, ZWO 290MM, D5300 astro modified
Nina, Bootcamped Mac Mini control computer, RDP to iMAC
110 amp hour lead acid deep discharge battery for field power
Electrical Engineer, Retired


Android for ExploreStars and Windows for ASCOM?

 

Hi Everyone - nub here...
Just received my EXOS 2 mount, but have yet to load the any software for it until I understand the future implications of loading one software App platform versus another.
I was planning on loading the Android ExploreStars App onto my new Samsung Galaxy Tab A 10, but I know that I will eventually want move to AP using a guide camera w/PHD2 with maybe some planetarium software. The question is: Can the PMC-Eight controller use both the Android App for ExploreStars and Windows for ASCOM drivers simultaneously? Concern is once I load the Android App software, am I stuck with it? Or said another way; does it hard code some info/software into the PMC controller that will later mess up with loading a Win 10 ASCOM type software? If not, can the Android be wireless and the ASCOM Serial port connected at the same time?
Any help or recommendations with this is appreciated!


Re: EXOS 2 GT Payload Capacity

Jerry Hubbell - Explore Scientific VP Engineering
 

On Mon, May 11, 2020 at 04:01 PM, Jerry Hubbell - Explore Scientific VP Engineering wrote:
The payload capacity specified for the EXOS 2 mount is 28 lbs. for visual use. Typically you reduce this to 70% for astrophotography, some reduce it to 50%.
We actually have increased the weight capacity for the EXOS 2 PMC-Eight mount to 40 lb. visual and 28 lb. for astrophotography.
 
--
Jerry Hubbell
Vice President of Engineering

Explore Scientific, LLC.
jrh at explorescientific.com

www.explorescientificusa.com
1010 S. 48th Street
Springdale, AR 72762
1-866-252-3811

Author: Scientific Astrophotography: How Amateurs Can Generate and Use Professional Imaging Data
             Remote Observatories for Amateur Astronomers: Using High-Powered Telescopes From Home


Mark Slade Remote Observatory (MSRO) IAU MPC W54 Equipment
Wilderness, VA
Mounts
: ES PMC-Eight G11 + Telescope Drive Master (TDM)
Scopes: ES 165 FPL-53 ED APO CF, ES 102 FCD100 ED APO CF
Cameras:  QHY174M-GPS + FW, QHY163C
Misc: 3-inch 0.7x Focal Reducer Field Flattener, Filters: Luminance,
Red, V-band Photometric, Diffuser, 200 lpmm Spectral Grating

Software: MaxIm DL 6, Cartes du Ciel, Astrometrica, AstroImageJ, AutoStakkert!


Re: Mounting camera to EXOS2 #EXOS2 #astrophotography

Nemesis2a
 

I too had the same problem when I got my EXOS2, but I improvised until I et smaller counter weight.


Re: Mounting camera to EXOS2 #EXOS2 #astrophotography

 

Counterweights?  
 
Yes, the two 5's that shipped with mine were overkill.  Should have been one like that and one half the size.  Better for customer value and would save ES some money as well.  They took the mount's overall weight rating a bit too literally when they sized those.  :-)
 
When I first got my mount, I set up very briefly for visual, and I could not balance my 102x621mm refractor with them.  Had to buy a 2kg counterweight to make that work.
 
That didn't last long.  Once I started hanging a camera off the back end and a guidescope off the top, I was able to retire the 2kg and use one of the original 5kg counterweights.  
 
--
Mounts: ES PMC-8 EXOS2
Scopes: SV 102EDT, ZWO 60/280 Guide
Cameras:  Nikon D5300, Altair GPCAM2 290M
Software: ASCOM, CdC, AstroTortilla, BYN Pro, Sharpcap, PHD2
Computer:  Thinkpad x230, Win7Pro/64


Re: Mounting camera to EXOS2 #EXOS2 #astrophotography

Patrick Maher
 

I second the need for a lighter, much lighter, counterweight.  The 9.9 lb counterweight will be far too heavy for just a camera.  

Patrick
--
Explore Scientific iEXOS-100 and EXOS-2GT (non-PMC)
Explore Scientific ED 102mm Refractor


Re: Astrophotography Done with the iEXOS-100, EXOS 2, and G11 Post your Pictures and Details! Lets Show What These Mounts Can Do. #G11 #astrophotography #iEXOS-100 #EXOS2

Dave Cherry
 

If these are practice runs . then I really want to see what you can do when you've finished practicing! , with your equivalent 5.4 meters of telescope!
Nice Pictures,


Cheers
Dave

--
Scopes: Sky Watcher 200PDS, Skywatcher 72ED
Mount: Explore Scientific PMC8 EXO2
Cameras: ASI 294MCPRO Coooled, Altair guide cam + 50mm scope
Software: Sharpcap Pro ,PH2, Stelarium Startools


Re: Astrophotography Done with the iEXOS-100, EXOS 2, and G11 Post your Pictures and Details! Lets Show What These Mounts Can Do. #G11 #astrophotography #iEXOS-100 #EXOS2

Harry
 

JR, great pictures! May I ask you about the stability and any other comments you have regarding your mount. I also have the iExos 100 with the stock tripod. I see you have the ST3 tripod with the Skymax 180mm Maksutov . I am considering a similar upgrade, and am wondering how yours is working out.
Thanks, Harry

--
Harry
Vero Beach, FL
Scopes: ES  ED80CF, ES AR102,  Meade ETX 90 EC (Deforked)
Mounts: ES iExos 100-PMC Eight, ExploreStars IPAD & Fire HD8
Nikon D600, D5500, MacOS, Starry Sky Stacker, Lightroom, Affinity Photo


Re: Astrophotography Done with the iEXOS-100, EXOS 2, and G11 Post your Pictures and Details! Lets Show What These Mounts Can Do. #G11 #astrophotography #iEXOS-100 #EXOS2

jrichard333 <jrichard333@hotmail.com>
 

Good day and thank you very much.

 

JR

 

From: MAIN@ESPMC-Eight.groups.io [mailto:MAIN@ESPMC-Eight.groups.io] On Behalf Of prmailers
Sent: Monday, July 20, 2020 12:35 AM
To: MAIN@ESPMC-Eight.groups.io
Subject: Re: [ESPMC-Eight] Astrophotography done with the iEXOS-100 and EXOS 2 post your picture and details lets show what this mount can do. #iexos-100 #EXOS2 #astrophotography

 

Nice!!!

 

 

 

Sent from my T-Mobile 4G LTE Device

 

 

-------- Original message --------

From: "jrichard333 <jrichard333@...>" <jrichard333@...>

Date: 7/19/20 11:58 PM (GMT-05:00)

To: MAIN@ESPMC-Eight.groups.io

Subject: [ESPMC-Eight] Astrophotography done with the iEXOS-100 and EXOS 2 post your picture and details lets show what this mount can do. #iexos-100 #EXOS2 #astrophotography

 

Good day all,

 

Mars and Jupiter were captured during an onslaught of intermittent cloud clover.

 

I view all of these images as practice runs.  I am still learning and developing my skill set.

I need a bit more work on Mars, but I can see slight improvement, although chromatic

aberrations are running wild.

 

Equipment:

Camera: Canon 70D

Date:  July 12, 2020

Target 1: Jupiter; altitude. 30-degrees

Target 2:  Mars; altitude 35-degrees

Telescope:  Sky-Watcher Skymax 180mm Maksutov @2700mm

Total focal length/ 2X Teleconverter:  5400mm

Filter:  2” LiPo/ Glow

Mount:  iEXOS-100/ ST3/ AZ Adjuster

Software:  FastStone Image viewer/  FastStone Photo Resizer

Moon:  54.7% luminance

 

Mars is getting more circular, which is a good thing J.

 

Jupiter; opposition missed due to cloud cover.  I do like the color

of Jupiter…pretty vibrant.  This is a GIF file.  But it does not work

embedded into this message.  I wanted to see the difference between

color and shades of grey.  Shades of grey is better.

 

JR


Re: Astrophotography Done with the iEXOS-100, EXOS 2, and G11 Post your Pictures and Details! Lets Show What These Mounts Can Do. #G11 #astrophotography #iEXOS-100 #EXOS2

Bob Trepiccione
 

Nice!!!



Sent from my T-Mobile 4G LTE Device


-------- Original message --------
From: "jrichard333 <jrichard333@...>" <jrichard333@...>
Date: 7/19/20 11:58 PM (GMT-05:00)
To: MAIN@ESPMC-Eight.groups.io
Subject: [ESPMC-Eight] Astrophotography done with the iEXOS-100 and EXOS 2 post your picture and details lets show what this mount can do. #iexos-100 #EXOS2 #astrophotography

Good day all,

 

Mars and Jupiter were captured during an onslaught of intermittent cloud clover.

 

I view all of these images as practice runs.  I am still learning and developing my skill set.

I need a bit more work on Mars, but I can see slight improvement, although chromatic

aberrations are running wild.

 

Equipment:

Camera: Canon 70D

Date:  July 12, 2020

Target 1: Jupiter; altitude. 30-degrees

Target 2:  Mars; altitude 35-degrees

Telescope:  Sky-Watcher Skymax 180mm Maksutov @2700mm

Total focal length/ 2X Teleconverter:  5400mm

Filter:  2” LiPo/ Glow

Mount:  iEXOS-100/ ST3/ AZ Adjuster

Software:  FastStone Image viewer/  FastStone Photo Resizer

Moon:  54.7% luminance

 

Mars is getting more circular, which is a good thing J.

 

Jupiter; opposition missed due to cloud cover.  I do like the color

of Jupiter…pretty vibrant.  This is a GIF file.  But it does not work

embedded into this message.  I wanted to see the difference between

color and shades of grey.  Shades of grey is better.

 

JR


Astrophotography Done with the iEXOS-100, EXOS 2, and G11 Post your Pictures and Details! Lets Show What These Mounts Can Do. #G11 #astrophotography #iEXOS-100 #EXOS2

jrichard333 <jrichard333@hotmail.com>
 

Good day all,

 

Mars and Jupiter were captured during an onslaught of intermittent cloud clover.

 

I view all of these images as practice runs.  I am still learning and developing my skill set.

I need a bit more work on Mars, but I can see slight improvement, although chromatic

aberrations are running wild.

 

Equipment:

Camera: Canon 70D

Date:  July 12, 2020

Target 1: Jupiter; altitude. 30-degrees

Target 2:  Mars; altitude 35-degrees

Telescope:  Sky-Watcher Skymax 180mm Maksutov @2700mm

Total focal length/ 2X Teleconverter:  5400mm

Filter:  2” LiPo/ Glow

Mount:  iEXOS-100/ ST3/ AZ Adjuster

Software:  FastStone Image viewer/  FastStone Photo Resizer

Moon:  54.7% luminance

 

Mars is getting more circular, which is a good thing J.

 

Jupiter; opposition missed due to cloud cover.  I do like the color

of Jupiter…pretty vibrant.  This is a GIF file.  But it does not work

embedded into this message.  I wanted to see the difference between

color and shades of grey.  Shades of grey is better.

 

JR


Re: Cygnus Loop #G11

Dan Kahraman <dkahra213@...>
 

Jennifer:

Gorgeous photos.

Dan Kahraman

On Sun, 19 Jul 2020 at 19:57, Wes Mcdonald <wesmcd6@...> wrote:
Jennifer:

WOWOWOW!!! Fantastic
wes.


--
Wes, Southport NC
EXos2-GT PMC-8, iExos 100
ES ED 127, 10" LX200GPS+wedge, Astro-Tech 8" Newt, ETX-90, 60mm no-name guide scope ~ 260mm FL
Polemaster, Orion ST-80 and SAG, ZWO 290MM, D5300 astro modified
Nina, Bootcamped Mac Mini control computer, RDP to iMAC
110 amp hour lead acid deep discharge battery for field power
Electrical Engineer, Retired


Re: Cygnus Loop #G11

Wes Mcdonald
 

Jennifer:

WOWOWOW!!! Fantastic
wes.


--
Wes, Southport NC
EXos2-GT PMC-8, iExos 100
ES ED 127, 10" LX200GPS+wedge, Astro-Tech 8" Newt, ETX-90, 60mm no-name guide scope ~ 260mm FL
Polemaster, Orion ST-80 and SAG, ZWO 290MM, D5300 astro modified
Nina, Bootcamped Mac Mini control computer, RDP to iMAC
110 amp hour lead acid deep discharge battery for field power
Electrical Engineer, Retired


Cygnus Loop #G11

Jennifer Shelly
 

An image of the Cygnus Loop shot over two nights with my ES G-11 PMC-8 and ES 127 FCD-100 with 3'' FF / O.7x FR.
Still working out the back focus with the FF/FR, but I am getting closer to the correct back focus.  Image details below.

Date(s): 07/07/2020 & 07/11/2020
Target Catalogue: IC 1340  /NGC 6979 / NGC C6960
Target Name: Cygnus Loop ~ Veil Nebula / Pickering's Triangle / Witch's Broom
Bortle Class: 7
Mount: ES G-11 PMC-8
Telescope: ES 127 FCD-100
FF/FR: ES 3" 0.7x FR/FF
Baader UFC
Filter: 2" L-enHance
Focuser: Moonlite CFL & V2 HR Stepper Motor
Camera: QHY128C
Bin: 1x1
Gain: 3,200
Offset: 80
Temp: -10C
Lights: 18 x 300s / 5 x 600s
Darks: 10 x 300s / 5 x 600s
Bias: 50 x 0.0004s
Flats: 10 x 0.208s
Dark Flats: 10 x 0.208s


--
Sincerely,

Jennifer Shelly
AstroPorch, VA

Mounts
: ES PMC-8 G-11, ES PMC-8 EXOS-2
Scopes: ES ED127 FCD-100, ES Levy Comet Hunter, ES N208CF, QHY Mini Guide Scope, Solomark F60 Guide Scope
Cameras: QHY600M, QHY128C, QHY168C
Misc: MoonLite CFL 2.5 / High Res Stepper / V2 Mini Controller, Baader SteelTrack NT / SteelDrive II, Baader UFC, Optolong 2" L-Pro / L-eNhance, QHY CFW3-L, Baader 2” LRGBSHO CCD
Imaging Software:  NINA, APT, SharpCap Pro
Processing Software: PixInsight, Lightroom, Premiere Elements


Re: Mounting camera to EXOS2 #EXOS2 #astrophotography

Brad Becker
 

Jennifer:

Thanks for your feedback.  There seems to be a limited selection (ie can't find one) of 10" or longer Vixen style dovetails tall enough for the mount sporting 3/8" screw heads other than what ES offers.  I'm sure its great .. and may go ahead purchasing it .. but am curious what else is out there as it seems to be a bit of overkill for my needs.

I'm going to use the Olympus OM-D E-M10 Mark II which is micro four third's (smaller lenses also) and was hoping the combination of less camera weight and beefier 3/8" ball heads would be adequate but may have to reconsider.  How are alt/az adjustments made without one?

I'm chuckling because if we can spend 2 - 3 pages discussing a simple DSLR mount what does the future hold for an actual scope attached.


Re: Mounting camera to EXOS2 #EXOS2 #astrophotography

Bob Trepiccione
 

Great info!



Sent from my T-Mobile 4G LTE Device


-------- Original message --------
From: "Jennifer Shelly via groups.io" <drunkendogg@...>
Date: 7/19/20 1:07 PM (GMT-05:00)
To: MAIN@ESPMC-Eight.groups.io
Subject: Re: [ESPMC-Eight] Mounting camera to EXOS2

Harry:

That ball head adapter is too short.   I know because I tried it with my EXOS-2.  The dovetail clamp on the EXOS-2 will not allow the camera/lens to be moved forward or backward when balancing the mount.  


Brad:

You want to find a Vixen style dovetail with at least 10 inches in length that will allow you to move the camera/lens forward and backward to balance the DEC axis.  When you balance the camera/lens for the DEC axis you will find the side with the motor on the DEC axis will be heavy and the camera/lens will want to rotate in that direction.  You can try to mitigate that that by adding another dovetail on top of that to form a + (plus) sign and mount the camera on the opposite side.  I do not recommend using a ball head because it will move.  You may not see it happening, but it will move.  And last but not least counterweights.  Depending on the weight of your camera/lens you mat not need a counterweight to balance the RA axis.  You might not need the counterweight bar.  Just experiment with various configurations and don’t be surprised if it takes up a whole day. If you think you need a counter weight you can buy a 7.5 lb Skywatcher counterweight.  Just make sure the borehole is the correct size.  ALWAYS have a hand very close to your equipment, so you can grab it when balancing the RA and DEC axis.  You do not want to have your equipment strike the tripod of the mount and damage your equipment.
--
Sincerely,

Jennifer Shelly
AstroPorch, VA

Mounts
: ES PMC-8 G-11, ES PMC-8 EXOS-2
Scopes: ES ED127 FCD-100, ES Levy Comet Hunter, ES N208CF, QHY Mini Guide Scope, Solomark F60 Guide Scope
Cameras: QHY600M, QHY128C, QHY168C
Misc: MoonLite CFL 2.5 / High Res Stepper / V2 Mini Controller, Baader SteelTrack NT / SteelDrive II, Baader UFC, Optolong 2" L-Pro / L-eNhance, QHY CFW3-L, Baader 2” LRGBSHO CCD
Imaging Software:  NINA, APT, SharpCap Pro
Processing Software: PixInsight, Lightroom, Premiere Elements


Re: Mounting camera to EXOS2 #EXOS2 #astrophotography

Jennifer Shelly
 

Harry:

That ball head adapter is too short.   I know because I tried it with my EXOS-2.  The dovetail clamp on the EXOS-2 will not allow the camera/lens to be moved forward or backward when balancing the mount.  


Brad:

You want to find a Vixen style dovetail with at least 10 inches in length that will allow you to move the camera/lens forward and backward to balance the DEC axis.  When you balance the camera/lens for the DEC axis you will find the side with the motor on the DEC axis will be heavy and the camera/lens will want to rotate in that direction.  You can try to mitigate that that by adding another dovetail on top of that to form a + (plus) sign and mount the camera on the opposite side.  I do not recommend using a ball head because it will move.  You may not see it happening, but it will move.  And last but not least counterweights.  Depending on the weight of your camera/lens you mat not need a counterweight to balance the RA axis.  You might not need the counterweight bar.  Just experiment with various configurations and don’t be surprised if it takes up a whole day. If you think you need a counter weight you can buy a 7.5 lb Skywatcher counterweight.  Just make sure the borehole is the correct size.  ALWAYS have a hand very close to your equipment, so you can grab it when balancing the RA and DEC axis.  You do not want to have your equipment strike the tripod of the mount and damage your equipment.
--
Sincerely,

Jennifer Shelly
AstroPorch, VA

Mounts
: ES PMC-8 G-11, ES PMC-8 EXOS-2
Scopes: ES ED127 FCD-100, ES Levy Comet Hunter, ES N208CF, QHY Mini Guide Scope, Solomark F60 Guide Scope
Cameras: QHY600M, QHY128C, QHY168C
Misc: MoonLite CFL 2.5 / High Res Stepper / V2 Mini Controller, Baader SteelTrack NT / SteelDrive II, Baader UFC, Optolong 2" L-Pro / L-eNhance, QHY CFW3-L, Baader 2” LRGBSHO CCD
Imaging Software:  NINA, APT, SharpCap Pro
Processing Software: PixInsight, Lightroom, Premiere Elements


Re: UPDATED FIRMWARE NOW AVAILABLE #ExploreScientific #FIRMWARE

Dave Cherry
 

Ok thanks Jerry

I’d better flash it in then at some point.

 

Cheers

Dave

 

 

Sent from Mail for Windows 10

 

From: Jerry Hubbell - Explore Scientific VP Engineering
Sent: Sunday, July 19, 2020 3:51 PM
To: MAIN@ESPMC-Eight.groups.io
Subject: Re: [ESPMC-Eight] UPDATED FIRMWARE NOW AVAILABLE #ExploreScientific #FIRMWARE

 

On Sun, Jul 19, 2020 at 10:49 AM, Dave Cherry wrote:

Does this new firmware have any advantages if you are pulse guiding with a guide scope?
I haven't upgraded yet as it is working fine for me just as it is.

Hi Dave,
There have been no significant changes recently to the pulse guiding code, but there is a significant change that impacts the performance of the slews that you 
would definitely want to have.
 
--
Jerry Hubbell
Vice President of Engineering
Explore Scientific, LLC.
jrh at explorescientific.com

www.explorescientificusa.com
1010 S. 48th Street
Springdale, AR 72762
1-866-252-3811

Author: Scientific Astrophotography: How Amateurs Can Generate and Use Professional Imaging Data
             Remote Observatories for Amateur Astronomers: Using High-Powered Telescopes From Home


Mark Slade Remote Observatory (MSRO) IAU MPC W54 Equipment
Wilderness, VA
Mounts
: ES PMC-Eight G11 + Telescope Drive Master (TDM)
Scopes
: ES 165 FPL-53 ED APO CF, ES 102 FCD100 ED APO CF
Cameras
:  QHY174M-GPS + FW, QHY163C
Misc
: 3-inch 0.7x Focal Reducer Field Flattener, Filters: Luminance,
Red, V-band Photometric, Diffuser, 200 lpmm Spectral Grating

Software
: MaxIm DL 6, Cartes du Ciel, Astrometrica, AstroImageJ, AutoStakkert!

 

Virus-free. www.avg.com

 

 


--
Scopes: Sky Watcher 200PDS, Skywatcher 72ED
Mount: Explore Scientific PMC8 EXO2
Cameras: ASI 294MCPRO Coooled, Altair guide cam + 50mm scope
Software: Sharpcap Pro ,PH2, Stelarium Startools


Re: UPDATED FIRMWARE NOW AVAILABLE #ExploreScientific #FIRMWARE

kevin power
 

Is the new update recent? Had my EXOS 2 for just over a month and installed latest at the time.

Thanks

Kev


From: MAIN@ESPMC-Eight.groups.io <MAIN@ESPMC-Eight.groups.io> on behalf of Jerry Hubbell - Explore Scientific VP Engineering <jrh@...>
Sent: Sunday, July 19, 2020 3:51:51 PM
To: MAIN@ESPMC-Eight.groups.io <MAIN@ESPMC-Eight.groups.io>
Subject: Re: [ESPMC-Eight] UPDATED FIRMWARE NOW AVAILABLE #ExploreScientific #FIRMWARE
 
On Sun, Jul 19, 2020 at 10:49 AM, Dave Cherry wrote:
Does this new firmware have any advantages if you are pulse guiding with a guide scope?
I haven't upgraded yet as it is working fine for me just as it is.
Hi Dave,
There have been no significant changes recently to the pulse guiding code, but there is a significant change that impacts the performance of the slews that you 
would definitely want to have.
 
--
Jerry Hubbell
Vice President of Engineering

Explore Scientific, LLC.
jrh at explorescientific.com

www.explorescientificusa.com
1010 S. 48th Street
Springdale, AR 72762
1-866-252-3811

Author: Scientific Astrophotography: How Amateurs Can Generate and Use Professional Imaging Data
             Remote Observatories for Amateur Astronomers: Using High-Powered Telescopes From Home


Mark Slade Remote Observatory (MSRO) IAU MPC W54 Equipment
Wilderness, VA
Mounts
: ES PMC-Eight G11 + Telescope Drive Master (TDM)
Scopes: ES 165 FPL-53 ED APO CF, ES 102 FCD100 ED APO CF
Cameras:  QHY174M-GPS + FW, QHY163C
Misc: 3-inch 0.7x Focal Reducer Field Flattener, Filters: Luminance,
Red, V-band Photometric, Diffuser, 200 lpmm Spectral Grating

Software: MaxIm DL 6, Cartes du Ciel, Astrometrica, AstroImageJ, AutoStakkert!


Re: UPDATED FIRMWARE NOW AVAILABLE #ExploreScientific #FIRMWARE

Jerry Hubbell - Explore Scientific VP Engineering
 

On Sun, Jul 19, 2020 at 10:49 AM, Dave Cherry wrote:
Does this new firmware have any advantages if you are pulse guiding with a guide scope?
I haven't upgraded yet as it is working fine for me just as it is.
Hi Dave,
There have been no significant changes recently to the pulse guiding code, but there is a significant change that impacts the performance of the slews that you 
would definitely want to have.
 
--
Jerry Hubbell
Vice President of Engineering

Explore Scientific, LLC.
jrh at explorescientific.com

www.explorescientificusa.com
1010 S. 48th Street
Springdale, AR 72762
1-866-252-3811

Author: Scientific Astrophotography: How Amateurs Can Generate and Use Professional Imaging Data
             Remote Observatories for Amateur Astronomers: Using High-Powered Telescopes From Home


Mark Slade Remote Observatory (MSRO) IAU MPC W54 Equipment
Wilderness, VA
Mounts
: ES PMC-Eight G11 + Telescope Drive Master (TDM)
Scopes: ES 165 FPL-53 ED APO CF, ES 102 FCD100 ED APO CF
Cameras:  QHY174M-GPS + FW, QHY163C
Misc: 3-inch 0.7x Focal Reducer Field Flattener, Filters: Luminance,
Red, V-band Photometric, Diffuser, 200 lpmm Spectral Grating

Software: MaxIm DL 6, Cartes du Ciel, Astrometrica, AstroImageJ, AutoStakkert!

2701 - 2720 of 9972