I put an acorn nut on the end of the screw that raises the thing. That seemed to reduce friction quite a bit, but it constrains how low the altitude can be set to. I have mine at 33 degrees and it

No. It works fine with iPadOS 16.4 in my 6th gen. Be sure to load firmware .02 or .03. If your iPad is having issues make sure the pmc8 is in udp mode if it is an iexos. Otherwise I have no

Hey Leandro, can you provide a video of the problems you are having for me. -- Tyler Bowman - Customer Service Office +1(866) 252-3811 Ext: 516 Fax +1(479) 717-2898

Wes, So do you think the latest update caused the problem with the iPad? I guess I should have tested before the update. Phil

Found this online. Im seeing the same wobbly motor rotation on mine. https://stargazerslounge.com/topic/357104-iexos-100-stepper-motor-nonlinearity/ Pointing out to be the chip controlling the motor

Thanks for the reply Bob, I will check it out!

Gokhan, Not sure what you could do about that - any solution would be constrained a bit by the casting material and mount base itself. But... if bending is a problem, that just says (to me, anyway)

Hey all, first time posting here, I've had the ES exos 2 pmc8 for a couple years now and i'm rly impressed of what it can do, even with heavy load and high'ish focal lengths but I'm having a hard time

Opening a new thread as requested. When selecting tracking ON on the Asiair mount panel the motor vibrates a lot and spins irregularly. It continuously starts and stops. Green light on the mount

This post is OFF TOPIC and this topic/thread should have MOVED to the Applications sub group. Please create a new thread for your issue. I am locking this thread now. It should have been locked and

I just opened the little plastic cover on the RA side that has the motor and the worm wheel. Looks like the motor spins irregularly and with a lot of vibration. Tried it with no guiding. Just mount

Thanks guys - gotta try your advices once we have clear again. Clear Skies everybody! Vlad Ing.arch.Vladimír Schmidt,AA 0907 654 916 www.zvarchitects.sk

Just wanted to hop in quickly, before you shift the conversations to the Applications sub-group. I had a similar issue, and found that telling the asiair to flip the meridian would often help (as I

My iPad is a 5th gen running 14.6. So I don’t think it uses an M1 chip. I’m not an iPad person but it looked like a good way to control the mount considering the IP address issues with the

Hi all, Vlad, sorry to hear you are having problems too. Last night i did the polar alignment with the asiair and got to be 8” off. The night i had terrible trailing at 30 secs and up i was at

Phil: Is your Ipad M1-based per chance? Wes -- Wes, Southport NC EXos2-GT PMC-8, iExos 100 ES ED 127, 10" LX200GPS+wedge, Astro-Tech 8" Newt, ETX-90, 60mm no-name guide scope ~ 260mm FL Polemaster,

Please post questions about asi air in the applications subgroup. -- Wes, Southport NC EXos2-GT PMC-8, iExos 100 ES ED 127, 10" LX200GPS+wedge, Astro-Tech 8" Newt, ETX-90, 60mm no-name guide scope ~

Thank you so much Alan! I’ll try to fix issues you suggested, hopefully it will be just this… I use ZWO ASI120mc-s as guiding cam, Artesky Ultraguide 32/130mm as

Hi Vladimir, looking at your guiding screen you are not in focus plus your exposure is too low, should be about 2 seconds and your gain seems high, you have not specified which guide camera you are

Hi, I have very same problem with autoguiding on ASIAIR Pro, mount iEXOS100 pmc8 - starts ok then very quickly the graph curves fall apart. Also, when I let it just track (no guiding), after few